RESET ERROR 21000068 ON EPSON T50 AND T60

Reset Error 21000068 On Epson T50 And T60, Have you get an error 21000068 when resetting your Epson Epson T50 or T60 and I see no solution to avoid the problem. Why not try this advice, but to restore this method is not recommended for the beginner and the user must understand what you are doing. These tips from Jagdish Rathore (India) and has granted me permission to post to this blog. It has also been the publication of this method to restore his blog at: http://www.epsonservice.blog.com/. If you have no knowledge of PCB and electronics, I recommend not trying to restore méthode.

Here the adjustment method :
Turn off the printer and printing files.
Open your advice Epson main board. You can see an 8-pin CMOS IC. Thats a waste of ink Epson against CI and found in all Epson printers.
You can configure your printer without resetter along these roads.
Solder pins 1,2,3,4 no cable as shown in the image and the printer now "second 20"
After 20 seconds turn off the printer and remove the pin welding cable no. 1,2,3,4 (back in original)
Now, turn on your printer
And now the printer is resetTag: Reset Error 21000068 On Epson T50 And T60

Read more

How Replace Color Cartridge on Epson 600Q Stylus ?

How Replace Color Cartridge on Epson 600Q Stylus ? The Epson Stylus 600Q is an inkjet printer that uses an ink cartridge Epson S020093 Epson S020089 black and color ink cartridge. The cartridges are housed in slots in the carriage is in the inside right of the printer - black in the slot on the left and the right color. Color cartridge replacement is necessary when the "color ink" or flashing light is on and when the cartridge is more than six months and the production of low quality or faded prints. 

Instructions 1 Turn on the Epson 600Q. Fold down the output tray and lift the printer cover.
2 Press the "cleansing" in the control panel for at least three seconds. Wait for the cartridge carrier to slide to the left of its rest position under the housing right side of the printer and the "Power" light will flash. If you want to remove a used cartridge, press the "Load / Eject" button instead.
3 Place your finger on the tab on the front of the cartridge slot and lift color ink cartridge cover.
4 Lift the cartridge slot, reserved for disposal.
5 Remove the color cartridge from its packaging. Hold the yellow tape at the top of the cartridge and gently pull it.
6 Place the new cartridge over the color cartridge slot with the arrow on the top label facing the printer. Insert the cartridge into the slot and then put on the lid and press firmly into place.
7 Press the "Clear" and lower the top of the printer in its original position to begin charging the ink. Wait about two minutes. When the "Power" light stops flashing and you can not hear the charging process will start printing again. 

Read more

HOW TO RESET CHIP ON EPSON 69 PRINTER CARTRIDGE

How to Reset the Chip on an Epson 69 Printer Cartridge,
Epson 69 black ink cartridges are used in a wide range of inkjet printers Epson. Every 69 Epson cartridge contains a chip that controls the amount of ink used. If a cartridge is refilled after the ink runs low, the chip must be restarted for the Epson printer to identify the cartridge as full. Epson chip resetter is required to redress the chip.

Instructions
things you need:
Epson chip resetter 

1 Put the Epson 69 cartridge so that the gold contacts on the bottom of the cartridge facing the metal pins on the chip resetter.
2 Press the Epson 69 cartridge in the resetter so that the contacts are touching the gold leads. Hold the cartridge in place.
3 Release the Epson cartridge chip resetter after the green LED comes resetter steadily. The chip is reset.

Read more

How to print a configuration page on an HP LaserJet P3005 printer

To print a config page from a LaserJet P3005:

- Press the green Select button to bring up the menu.  (If the printer is idle, press the Select button twice, once to wake it up and once to bring up the menu.)
- Press the down arrow button twice until INFORMATION is displayed.
- Press the Select button.
- Press the down arrow button once until PRINT CONFIGURATION is displayed.
- Press the Select button.

Read more

How to print a configuration page on an HP LaserJet M1319f MFP

The configuration page on an HP printer gives you a lot of information.  The exact contents of the page vary from printer to printer, but some of the things you can generally find on a configuration page include the printers page count, serial number, current network setup, paper tray settings, and available memory.  To print a configuration page from a LaserJet M1319f MFP, follow the steps below.

- Press the Setup button on the printers operation panel (just below the display Lcd).
- Scroll through the menu options until you see Reports.
- Press the OK button.
- Scroll through the report options until you come to Config Report.
- Press OK to print out the configuration page.

Read more