The Epson Stylus CX4300 Counter Reset Utility

Repair the Epson CX4300 printer problem by following the troubleshooting guide. The Message “printer near end service life” or “printer end of service life”, it does not mean that you should throw the printer. There was no problem of your printer, the problem is that’s its maximum counter limit value have reach to its maximum allowed.To fix the this kind of problem you need to download the program and before opening the Epson adjustment utility, make sure that the power of the printer is on, properly connected to your computer and most of all there’s no pending print task in your printer.

The Epson Stylus CX4300 Printer Cartridges

 

Follow the steps below:

• Open AdjProg.exe
• Click Accept
• Click "OK"
• Click the Particular Adjustment Mode
• Select Waste ink pad counter
• Click OK
• Click Initialization (this will reset counter)
• Turn off the printer
• Then turn on again.

Finish!
Click here to download the counter resetter

Read more

The Epson Stylus CX3900 Repair Service Life Error

Reset the counter of CX3900 printer problem and print back to normal after following the troubleshooting guide. The Message “printer near end service life” or “printer end of service life”, it does not mean that you should throw the printer. There was no problem of your printer, the problem is that’s its maximum counter limit value have reach to its maximum allowed.To fix the this kind of problem you need to download the program and before opening the Epson adjustment utility, make sure that the power of the printer is on, properly connected to your computer and most of all there’s no pending print task in your printer.

The Epson Stylus CX3900 Printer Cartridges

Follow the steps below:

• Open AdjProg.exe
• Click Accept
• Click "OK"
• Click the Particular Adjustment Mode
• Select Waste ink pad counter
• Click OK
• Click Initialization (this will reset counter)
• Turn off the printer
• Then turn on again.

Finish

Click here to download the resetter

Read more

Here is the reset for the Canon Canon BJC 2000 BJC 2100 Series

Waste Error Reset :
ERROR : Used ink tank is full
1. Remove the Cartridge
2. Unplug the AC Power Cord
3. Close Front access panel
3. Hold down the RESUME/RESET button and plug in the AC power cord
4. Release RESUME/RESET after plugging in the AC Power cord.
5. Press the RESUME/RESET once within 5 seconds and release the RESUME/RESET .
6. Press and HOLD RESUME/RESET for two seconds or more and release it.
7. Press and HOLD RESUME/RESET for two seconds or more and release it.
8. Unplug AC Power Cord to set data
If you need nore info try here :
- http://www.neilslade.com/papers/inkjetstuff.html
Wem, Try soaking the print head in a shallow dish/plate of hot distilled water to remove any dried out ink. You may need to repeat the process a few times to fully unclog the print head.

Read more

I am currently in the process of cleaning the Waste Ink Tank

This methods is for almost all kind Canon printer.
My method is :
1. Unassemble the Printer , Has locking Tabs & 1 Screw.
2. Remove the Mechanism.
3. Remove the Power supply & the connector
4. Place the Base in a sink & remove the Pads
5. Wash the Base in Running Water .then Dry thoroughly.
6. Sqeeze wash the 2 pads in running warm water.until no Ink runs out.
7. Sqeeze dry all the excess water from the Pads & leave to Dry overnite.
8. Reassemble the printer & Run through the Reset as in Wess Post.

Read more

The waste ink Pads in Epson L110 printer

Hello friends, in my previous post, i have given you information about the ink resetting in Epson L110 printer.

Now yesterday, i have found out the location of the Waste ink Pad in Epson L110.

Just turn the Epson L 110 Printer around to the back, pull the paper in tray up, just next to the power plug socket, you would find a screw. Just use a star screw driver, to unscrew the screw.

This is the only lock to the Wast ink Pad set up. Now lock the check valve to the ciss tank, so that there is no out flow of ink, when you turn the printer upside down.

Remove the ciss tank from the main Printer frame.

Now turn the printer upside down 50%, not a 100 % upside down.

Now move the paper output tray from the bottom a little to the front. On the left side of the bottom of the Epson L 110 printer, the Waste Ink Pad is located, a big rectangular box, with Waste ink pads stuffed in it.

Now move the Waste Ink Pad compartment a little to the right, the chamber would unlock itself and pull the chamber out.

If you want to reuse the Waste Ink Pad, you could saturate the Waste Ink Pads in alcohol, then dry them and again use it in the printer.

But all i would suggest to use is a Waste Ink Tank bottle to be mounted new. This time in this printer, Epson technical department has thought very meticulously and done a new trick to stop refilling by bulk inks.

Commercially, there is no Waste Ink Tank Bottle or kit available in the market. But you can make one by yourself. I have already done a Waste Ink Tank myself. It is being tested for some time. 

Read more